How to Take Apart a Glock 26?

Author

Posted Sep 23, 2022

Reads 56

Living room in apartment

How to take apart a glock 26

The Glock 26 is a 9mm subcompact pistol. It was first introduced in 1994 and was designed for concealed carry. The Glock 26 has a polymer frame and a unique "Safe Action" trigger system. The trigger system is designed to be safe and easy to use.

The Glock 26 can be disassembled for cleaning and maintenance. The process is simple and does not require any special tools.

First, make sure the pistol is unloaded. Remove the magazine and check the chamber to make sure it is empty.

Next, remove the slide stop. The slide stop is located on the left side of the frame, just above the trigger. Pull the slide stop out with your finger.

Now, pull the slide off the front of the frame. The slide can now be removed by pulling it to the rear and then lifting it up and off the frame.

The barrel can now be removed from the slide. To do this, first remove the recoil spring assembly. The recoil spring assembly is located under the barrel. Pull it out and then set it aside.

Now, you can remove the barrel. The barrel can be pulled out of the slide by hand.

Once the barrel is removed, the recoil spring guide can be seen. The recoil spring guide is located in the front of the frame. It can be removed by unscrewing it with your fingers.

With the recoil spring guide removed, the slides can now be removed from the frame. The slides can be taken off by pulling them to the rear and then lifting them up and off the frame.

The Glock 26 can now be reassembled by reversing the above steps. First, put the slides back on the frame. Then, screw the recoil spring guide back in place.

Next, insert the barrel into the slide. Finally, put the recoil spring assembly back in place and then reattach the slide stop.

The Glock 26 is now ready to be used.

How do you take apart a glock 26?

How do you take apart a glock 26?

The Glock 26 is a 9mm subcompact pistol first introduced in 1994. It is similar in size to the Glock 19, but has a shorter barrel and shorter grip. The Glock 26 has a magazine capacity of 10 rounds, making it ideal for concealed carry.

To take apart a Glock 26, you will need a few tools. First, you will need a flathead screwdriver. You will also need a punch tool or a small diameter rod (about 3/16 inch).Using the flathead screwdriver, remove the two screws from the back plate of the slide. These screws are located at the top of the grip, just behind the slide release lever.

Once the screws are removed, the back plate can be carefully pried off. Be careful not to lose the small spring and plunger that are located under the back plate. With the back plate removed, you will now have access to the firing pin assembly.

Using the punch tool or small diameter rod, push out the firing pin assembly from the front of the slide. The firing pin assembly consists of the firing pin, firing pin spring, firing pin safety, and firing pin safety spring. With the firing pin assembly removed, the slide can now be slid off the front of the frame.

The Glock 26 can now be field stripped for cleaning and maintenance. To reassemble the pistol, simply reverse the process. Be sure to check that the firing pin assembly is properly seated in the front of the slide before replacing the back plate and screws.

What tools do you need to take apart a glock 26?

A Glock 26 is a 9mm subcompact handgun. The Glock 26 was introduced in 1995 and was designed to be a more concealable handgun for law enforcement and civilian customers. The Glock 26 has a shorter barrel and grip compared to the Glock 17, the full-size Glock 9mm handgun. The Glock 26 can be broken down into five main components: the slide, barrel, recoil assembly, frame, and magazine.

The slide is the upper part of the gun that the bullet travels through after being fired from the barrel. The barrel is the long metal tube that the bullet travels through. The recoil assembly is the mechanism that locks the slide and barrel together and absorbs the recoil from the gun being fired. The frame is the lower part of the gun that the slide, barrel, and recoil assembly attach to. The magazine is the cylinder that holds the bullets and feeds them into the gun.

To take apart a Glock 26, you will need a few tools. First, you will need a punch tool to remove the pins that hold the slide, barrel, and recoil assembly in place. Second, you will need a T-handle hex wrench to loosen and remove the barrel from the slide. Third, you will need a Phillips head screwdriver to remove the recoil assembly from the frame. Fourth, you will need a flat head screwdriver to remove the magazine release from the frame. Finally, you will need a hammer to tap out the magazine release from the frame.

With these tools, you can take apart a Glock 26 and clean it, inspect it, or replace parts.

How do you disassemble the slide from the frame of a glock 26?

There are a few steps required in order to disassemble the slide from the frame of a Glock 26. The first step is to make sure the gun is unloaded. Then, you need to remove the magazine by depressing the magazine release. With the magazine out, you can now pull the slide back and release the slide stop. The slide can now be removed from the frame.

In order to remove the barrel, you will first need to remove the recoil spring assembly. This can be done by depressing the spring cups and then removing the assembly. With the recoil spring assembly out, the barrel can now be removed.

To remove the sights, you will need to use a sight tool to push out the front sight. The rear sight can then be drifted out with a flathead screwdriver. With the sights removed, the slide is now ready to be taken apart for cleaning or other maintenance.

How do you remove the barrel from the slide of a glock 26?

Assuming you would like a step-by-step guide on how to remove the barrel from the slide of a Glock 26:

1. First, ensure that the gun is unloaded. Remove the magazine by depressing the magazine release and pulling the magazine out of the grip. Lock the slide back and visually inspect the chamber to make sure it is empty.

2. Next, identify the two small pins located above the trigger guard on either side of the frame. These are the frame locking pins.

3. Using a small punch or other pointed tool, push the right frame locking pin out from right to left. As you do this, the trigger assembly will become loose. You can remove it now if you wish, but it is not necessary.

4. Now push the left frame locking pin out from left to right. As you do this, the slide will become loose on the frame.

5. Grab the barrel near the muzzle and the slide near the rear and pull them apart. The barrel can now be removed from the slide.

How do you remove the recoil spring and guide rod from the barrel of a glock 26?

Assuming you would like a step-by-step guide on how to remove the recoil spring and guide rod from the barrel of a Glock 26:

1.remove the magazine and make sure the chamber is empty 2.lock the slide back and take a small punch or similar tool and push down on the takedown lever (this is located on the left side of the frame just behind the trigger) 3.while holding down the takedown lever, release the slide stop (this is the large lever on the right side of the frame just above the trigger guard) and let the slide move forward off the frame 4.remove the recoil spring assembly by holding the barrel and pushing the spring assembly out 5.remove the guide rod

With the spring and guide rod removed, the barrel can now be removed from the slide.

How do you remove the firing pin and firing pin spring from the slide of a glock 26?

The Glock 26 is a subcompact 9mm handgun. It is chambered for the 9x19mm Parabellum cartridge, and can also be fired with the .40 S&W and .357 SIG cartridges with the use of a barrel and magazine change. The Glock 26 has a magazine capacity of 10 rounds in a double-stack configuration.

The Glock 26 is striker-fired, with a "Safe Action" trigger system. The trigger pull is approximately 5.5 pounds (2.5 kg). The gun is made with a polymer frame and a steel slide.

To remove the firing pin and firing pin spring from the slide of a Glock 26, first remove the slide from the gun. Then, using a punch or a small screwdriver, push the firing pin retaining pin out from the left side of the slide.

With the retaining pin removed, the firing pin and its spring can now be removed from the right side of the slide. To do this, simply pull the firing pin out from the right side of the slide. The firing pin spring will come out with it.

How do you remove the extractor and extractor spring from the slide of a glock 26?

If you need to remove the extractor and extractor spring from the slide of your Glock 26, you will need to first remove the slide from the firearm. Once the slide is removed, you will need to use a punch tool or a small screwdriver to push down on the extractor spring until it is flush with the extractor. You can then use a small Allen key or a flathead screwdriver to remove the two screws that hold the extractor in place. With the screws removed, you can pull the extractor out of the slide. To remove the extractor spring, you will need to use a small punch tool or a paperclip to depress the retaining pin on the underside of the spring. Once the pin is depressed, you can pull the spring out of the slide.

How do you remove the trigger assembly from the frame of a glock 26?

Assuming you would like a complete answer on disassembling a Glock 26:

The Glock 26 is a semi-automatic pistol designed andmanufactured by Glock. It is chambered for the 9×19mm Parabellum cartridge, and is a compact version of the Glock 19, which is a mid-size pistol. The Glock 26 was introduced in 1995 and was Glock's first "subcompact" pistol.

The Glock 26 has a polymer frame with a steel slide and a magazine capacity of 10 rounds. The Glock 26 is similar in size and weight to the popular Ruger LC9s.

The Glock 26 is striker-fired, and has a trigger pull of 5.5 pounds (24.5 N). The pistol has a overall length of 6.29 inches (159.3 mm), a barrel length of 3.42 inches (87.0 mm), and a width of 1.26 inches (32.0 mm).

To remove the trigger assembly from the frame of a Glock 26, first remove the magazine and make sure the chamber is empty. Then, pull the slide back and release the slide stop. Next, push down on the slide release with a punch or small tool, and slide the slide forward off the frame.

The trigger assembly is now exposed. To remove it, depress the trigger, and while holding it depressed, remove the trigger pin by pushing it out from the left side with a punch or small tool.

With the trigger pin removed, the trigger assembly can now be removed from the frame by simply pulling it out.

How do you remove the magazine release and magazine release spring from the frame of a glock 26?

There are a few ways to remove the magazine release and magazine release spring from the frame of a Glock 26. One way is to use a punch and a small hammer to drive the punch through the magazine release hole. This will push the magazine release out of the frame. The other way is to use a small screwdriver to remove the two screws that hold the magazine release in place. After the screws are removed, the magazine release can be pulled out of the frame. The magazine release spring can then be removed by pushing on it with a small punch or screwdriver.

Frequently Asked Questions

What size punch do I need to disassemble a Glock?

This size punch is the right size to work with all of the Glock pins and helps facilitate breakdown. The Glock disassembly tool is an official Glock product and is part of the issued equipment given to Glock certified armorers.

How do you replace the cover plate on a Glock?

Glock owners should start by carefully removing the old cover plate by depressing the spring found in the gap and sliding it off. Once the old cover plate is off, slide the new one on and be careful to keep your thumb over the firing pin and extractor plunger, as they are under pressure until you slide the new cover plate on.

How to remove the slide from a Glock?

The slide on a Glock can be removed in a few simple steps. To do so, you'll need to use caution and wear safety glasses to protect your eyes. First, close the slide to make sure it's locked in place. Next, grip the gun and pull back the slide. Finally, disengage the slide lock and pull the slide off of the gun.

How do you replace the firing pin on a Glock?

1. Remove the BCG from the pistol by unsnapping the two clips and pulling it free. 2. Set the pistol on a padded surface so that the firing pin can be easily accessed. Be sure to use gloves to protect your hands when working with the firearm. 3.identify the small gap at the end of the firing pin assembly, depress the spring found in this gap and slide the cover plate off. Keep your thumb over the firing pin and extractor plunger while doing this as these are under pressure until you slide on new cover plate

Does the simple punch work with All Glocks?

Yes, the simple punch does work with all Glock pistols.

Brett Cain

Senior Writer

Brett Cain is an experienced blogger with a passion for writing. He has been creating content for over 10 years, and his work has been featured on various platforms. Brett's writing style is concise and engaging, making his articles easy to read and understand.