How to Lighten Marlin 336 Trigger?

Author Brett Cain

Posted Sep 5, 2022

Reads 109

Living room in apartment

There are many shooters who believe that the Marlin 336 trigger can be improved. Some believe that the addition of a light Trigger spring will lighten the trigger pull. While others believe that the judicious use of a Dremel tool can port and polish the trigger group to give a much-improved trigger pull. It is also possible to replace the stock trigger with an aftermarket replacement that is adjustable.

It is important to understand that there are different types of Marlin 336 triggers. The early Marlin 336 triggers had a bent trigger lever that was quite small in diameter. The later Marlin 336 triggers had a straight trigger lever that was larger in diameter. Some shooters believe that the best improvement that can be made to the Marlin 336 trigger is to install the later style Marlin 336 trigger with the straight trigger lever.

If you decide to install a light trigger spring, you should understand that this is a permanent modification that will void the warranty on your Marlin 336. When you install a light trigger spring, the sear release point is lowered. This means that the trigger pull will be lighter, but the rifle will also be easier to accidentally discharge. If you are going to install a light trigger spring, it is important to test the rifle thoroughly to make sure that it is safe to use.

If you decide to port and polish the trigger group, you should understand that this is also a permanent modification that will void the warranty on your Marlin 336. When you port and polish the trigger group, you are essentially enlarging the trigger clearance holes. This means that the trigger pull will be lighter, but the rifle will also be easier to accidentally discharge. If you are going to port and polish the trigger group, it is important to test the rifle thoroughly to make sure that it is safe to use.

There are aftermarket replacement triggers available for the Marlin 336. These triggers are adjustable, and they offer a significant improvement over the stock trigger. The aftermarket triggers are not cheap, but they are worth the investment if you are serious about improving the performance of your Marlin 336.

No matter which route you decide to go, it is important to understand that any modification you make to the Marlin 336 trigger will void the warranty. This is not a decision to be made lightly. Make sure that you understand the implications of any modification you make to the Marlin 336 trigger before you proceed.

What is the best way to lighten the trigger on a marlin 336?

There are a few ways to lighten the trigger on a marlin 336. One way is to file down the sear. This will reduce the amount of force needed to release the trigger. Another way is to replace the trigger spring with a lighter one. This will also reduce the amount of force needed to release the trigger. Finally, you can adjust the trigger adjustment screw. This will change the amount of travel the trigger has before it releases.

What are some of the benefits of lightening the trigger on a marlin 336?

There are many benefits to lightening the trigger on a marlin 336. One of the benefits is that it increases the accuracy of the rifle. When the trigger is heavier, it is more difficult to keep the rifle steady and on target. This is because the extra weight of the trigger pull can cause the rifle to move slightly off target. By lightening the trigger, the rifle will be easier to keep on target, resulting in increased accuracy.

Another benefit of lightening the trigger is that it can increase the rate of fire. This is because it takes less time and effort to pull the trigger when it is lighter. This means that the shooter can get off more shots in a shorter period of time. This can be beneficial in a number of situations, such as when trying to take down a fast moving target or when engaging multiple targets at once.

Overall, lightening the trigger on a marlin 336 can have a number of benefits. These benefits include increased accuracy and a higher rate of fire. These are just a few of the benefits that can be gained by lightening the trigger on a marlin 336.

How much can you expect to lighten the trigger on a marlin 336?

There is no definitive answer to this question as it will depend on the individual gun and the shooter's preference. However, there are a few things that can be considered when trying to determine how much to lighten the trigger on a marlin 336.

The first thing to consider is the use of the gun. If the gun is going to be used for hunting, then a lighter trigger may be desirable as it can help to prevent accidental discharge. However, if the gun is going to be used for recreational shooting or self-defense, then a heavier trigger may be preferable as it can help to ensure that the gun will only fire when the shooter intends it to.

The second thing to consider is the shooter's personal preference. Some shooters prefer a lighter trigger for reasons of personal comfort or because they feel it gives them more control over the gun. Others may prefer a heavier trigger because they feel it is safer or because they are more accustomed to shooting guns with heavier triggers. There is no right or wrong answer here, it is simply a matter of what the shooter prefers.

Finally, it is important to consider the gun itself. Some guns may have triggers that cannot be safely lightened without causing problems. In some cases, it may be possible to have the trigger worked on by a gunsmith in order to achieve the desired result. However, this should only be done by someone who is experienced in working on triggers, as it is possible to damage the gun if the work is not done properly.

In conclusion, there is no definitive answer to the question of how much to lighten the trigger on a marlin 336. However, there are a few factors that can be considered when making this decision. Ultimately, it is up to the shooter to decide what trigger weight is best for their individual needs.

Is it difficult to lighten the trigger on a marlin 336?

It can be difficult to lighten the trigger on a marlin 336, depending on how it is set up. The gun typically comes with a four-pound trigger, which is already pretty light. However, some people want an even lighter trigger, which can be achieved by adjusting the screw that controls the trigger's pull weight. This screw is located in the trigger guard, and turning it clockwise will lighten the trigger pull.

It's important to be careful when adjusting this screw, as you can easily make the trigger too light and cause the gun to misfire. A good rule of thumb is to turn the screw no more than one turn at a time, and then test the trigger pull before making any further adjustments. If you do end up making the trigger too light, you can always turn the screw back the other way to increase the pull weight.

As long as you're careful and take your time, it's not too difficult to lighten the trigger on a marlin 336. Doing so can make the gun easier and more enjoyable to shoot, and ultimately help you to become a better marksman.

What tools do you need to lighten the trigger on a marlin 336?

When it comes to lightening the trigger on a marlin 336, there are a few different tools that you may need in order to get the job done correctly. First, you will need a set of torx wrenches in order to remove the screws that secure the trigger guard assembly. Next, you will need a small punch or other sharp tool in order to remove the trigger pin. Finally, you will need a small file in order to smooth out the trigger sear.

Assuming that you have a marlin 336 that is in need of a trigger job, the first thing you will want to do is make sure that the firearm is unloaded. Once you have verified that the gun is unloaded, you can proceed to removing the screws that secure the trigger guard assembly. Once the screws have been removed, you can then take the trigger guard off of the gun.

With the trigger guard removed, you will then have access to the trigger assembly itself. At this point, you will want to take your small punch or other sharp tool and drive out the trigger pin. Once the trigger pin has been removed, you can then take thetrigger assembly apart.

Once the trigger assembly is apart, you will want to take a look at the trigger sear. If you notice that the trigger sear is excessively worn or has any burrs on it, you will want to use your small file to smooth it out. Once you have smoothed out the trigger sear, you can then reassemble the trigger assembly and trigger guard.

Once you have reassembled the trigger assembly and trigger guard, you can then proceed to reinstalling the trigger guard assembly onto the gun. Once the trigger guard assembly is back in place, you can then proceed to test the trigger pull. If you are satisfied with the trigger pull, you can then proceed to reassemble the gun.

How long does it take to lighten the trigger on a marlin 336?

It takes quite a bit of time and patience to lighten the trigger on a marlin 336. First, you need to remove the stock and then the action. With the action out, there is a small spring that needs to be removed. This is the trigger return spring. Next, you need to take out the trigger and sear assembly. The sear is held in place by a small set screw. Remove this screw and the sear will come out. The trigger can now be slid out of the trigger housing.

Now, take a look at the trigger return spring. This is the spring that you will need to remove in order to lighten the trigger pull. Using a pair of pliers, carefully remove the trigger return spring. Once the spring is out, you can now remove the trigger and sear assembly.

With the trigger and sear assembly out, you will now need to remove the trigger return spring. This is a small spring that is located behind the trigger. Using a pair of pliers, carefully remove the trigger return spring. Once the spring is out, you can now remove the trigger pin. This is the small pin that holds the trigger and sear together. With the trigger pin removed, you can now remove the trigger and sear from the housing.

Now, take a look at the trigger housing. You will notice that there are two small set screws located on the bottom of the housing. These set screws are what hold the trigger and sear in place. Using a small Allen wrench, remove these set screws. With the set screws removed, you can now slide the trigger and sear out of the housing.

You will now need to take a look at the trigger spring. This is the large spring that is located behind the trigger. Using a pair of pliers, carefully remove the trigger spring. Once the spring is out, you can now remove the trigger from the housing.

With the trigger removed, you can now take a look at the sear. You will notice that the sear has a small set screw located on the top of it. Using a small Allen wrench, remove this set screw. With the set screw removed, you can now slide the sear out of the housing.

You will now need to take a look at the trigger return spring. This is the small spring that is located behind the trigger. Using a pair of pliers, carefully remove the trigger return spring. Once

How much does it cost to lighten the trigger on a marlin 336?

How much does it cost to lighten the trigger on a marlin 336? This is a difficult question to answer because there are many variables that can affect the cost. The type of Marlin 336, the type of trigger, the desired lightness, and the gunsmith performing the work will all play a role in pricing. A ballpark estimate would be $100-$200.

The first variable is the type of Marlin 336. There are three main types of Marlin 336s- the original, the cowboy, and the tactical. The original Marlin 336 is the most basic model and will be the least expensive to modify. The cowboy model is the next step up and will be a bit more expensive. The tactical Marlin 336 is the top of the line and will be the most expensive to modify.

The next variable is the type of trigger. The original Marlin 336 came with a factory trigger that was not adjustable. If you want to adjust the trigger on an original Marlin 336, you will need to replace the factory trigger with an aftermarket one. Aftermarket triggers can cost anywhere from $50-$200. The type of trigger you choose will affect the cost.

The desired lightness is the next variable. The lighter the trigger, the more expensive it will be. A very light trigger may require some custom work which will drive up the cost.

The last variable is the gunsmith performing the work. If you use a gunsmith that specializes in Marlin 336s, they will likely charge a bit more than a general gunsmith. However, you will be more likely to get a better quality job.

In conclusion, the cost to lighten the trigger on a Marlin 336 depends on a few variables. The type of Marlin336, the type of trigger, the desired lightness, and the gunsmith performing the work will all play a role in pricing. A ballpark estimate would be $100-$200.

Is there a warranty on a trigger job?

There are many schools of thought on whether or not a warranty exists on a trigger job. The purpose of this essay is to explore the different perspectives on this topic and determine if there is a consensus on the matter.

Most gunsmiths will say that a trigger job is a personal preference and that once it is done, it cannot be undone. This means that if you are not satisfied with the results, you are not likely to get your money back or have the job fixed for free. There are some gunsmiths who will offer a warranty on their work, but this is not the norm.

There are a few schools of thought on whether or not a trigger job voids the warranty on a firearm. The first is that a trigger job is a permanent alteration to the firearm and therefore voids the warranty. The second is that a trigger job does not void the warranty as long as the original parts are not modified or replaced. The third is that it depends on the gunsmith who did the work and what their policy is.

There are a few things to consider when deciding if a warranty exists on a trigger job. The first is what the gunsmiths' policies are. The second is what the firearm manufacturer's policies are. The third is your personal preference.

Gunsmiths' policies:

As mentioned above, most gunsmiths do not offer a warranty on their work. This is because a trigger job is a personal preference and they cannot guarantee that you will be satisfied with the results. There are some gunsmiths who will offer a warranty, but this is not the norm.

Firearm manufacturer's policies:

Most firearm manufacturers do not void the warranty if you have a trigger job done. They understand that this is a personal preference and that you may not be satisfied with the results. However, they will not cover any damage that is done to the firearm during the trigger job.

Personal preference:

The most important factor to consider when deciding if a warranty exists on a trigger job is your personal preference. If you are not satisfied with the results of the trigger job, you are not likely to get your money back or have the job fixed for free. You should only have atrigger job done if you are sure that you want it and you are willing to accept the risks.

What is the turnaround time for a trigger job?

A trigger job is the process of installing new or upgraded parts in a firearm to improve its trigger pull. This can be done to any type of firearm, from a handgun to a rifle. The most common reason to do a trigger job is to improve the gun's accuracy. A lighter, smoother trigger pull makes it easier to fire the gun with less movement, which should result in tighter groups.

There are a few different ways to go about improving a trigger pull. The first is to simply replace the springs that control the movement of the trigger. This is the most basic form of trigger job, and is often all that is needed to make a significant improvement. The second method is to install an aftermarket trigger assembly. This is a more involved process, and usually requires some gunsmithing skills. Aftermarket trigger assemblies often offer a much lighter trigger pull than the stock parts, and can make a dramatic difference in accuracy.

The turnaround time for a trigger job can vary depending on the level of work involved. A basic spring replacement can usually be done in an afternoon. An aftermarket trigger assembly will take longer, often requiring a couple days to complete. Ultimately, the turnaround time for a trigger job will depend on the gunsmith performing the work and the extent of the modifications being made.

Frequently Asked Questions

Is the Marlin Model 336 still in production?

Although the Marlin 336 is no longer in production, there are still a number of them on the market.

What kind of gun is a Marlin Model 336?

A lever-action rifle and carbine made by Marlin Firearms.

Is the Marlin Model 36 still in production?

Yes, the Marlin Model 36 is still in production under the Ruger Firearms name.

How many Ruger Model 336 rifles were made?

According to Ruger, a total of 4,018,022 Model 336 rifles have been produced.

When did the Model 336XLR come out with a longer barrel?

The Model 336XLR came out with a longer barrel in 2006.

Brett Cain

Brett Cain

Writer at iHomeRank

View Brett's Profile

Brett Cain is an experienced blogger with a passion for writing. He has been creating content for over 10 years, and his work has been featured on various platforms. Brett's writing style is concise and engaging, making his articles easy to read and understand.

View Brett's Profile